20 Marking Hacks Every DIYer Should Know

Check out 20 incredible hacks that’ll assist in making your markings more precise and your working days more productive.

Learn and master the basics

Before we get too deep into the tricks and hacks before we get started, let’s take a break to ensure that we are aware of the basic rules of marking a cut. It is always best to mark the area on the board where the saw will make its first contact. If you’re using a circular saw typically, this is close to the edge of the board. However, the cut of a miter saw should be marked in center of the boards. If you can, mark it using a ‘V’ mark to decrease the chance of either side or the opposite. Check out this instructional video on marking a board prior to cutting it with a miter saw.

Simple Method of Marking Cylinders

It’s notoriously difficult for you to mark marks on curving surfaces. Dropping an edge straight or a measuring tape onto tubing , or PVC will provide you with the line you can mark, however it’s incredibly easy to move or roll your edge to mark a line. Make use of a length of angle iron to create several touches within the cylindrical, thereby stabilizing lines and making it easier to trace a mark using markers or pencils. If you have to take an exact measurement from the surface, you can simply put an ruler or tape measure over the smooth surface on which an angle iron. It’s a fantastic way to make an arduous task easy!

Don’t be afraid of hacking the Tool!

There’s no shortage in the number of specialized tools available and most are designed to make marking fast and simple. But it doesn’t change fact that it’s always that the ideal tool for the job you’re working on is either at home or being displayed on the shelves of the local hardware shop. This is why it’s crucial to take the time to learn how to adapt your tools to finish your project. One example of this is the clothespin tool that was submitted by a reader Bruce Kieffer.

Attach Trim to the Wall while Marking

One of the most common spots to commit a mistake while cutting trim is while transferring measurements from the wall to the station. Get rid of the risk using this easy trick! Place the trim on the wall and trace your design right on the wall on which it is to be put in. If the trim piece is too much wobble to keep in place, fix it up with the help of a temporary brad nail. Remove the brad from the back after you take out the trim piece and you’ll have just only a small hole to fill when you install. This is a great source for tips and tricks for finishing nailers.

Don’t trust factory Edges

We’ve experienced it all at some point: you’re working on an assortment of fresh boards or plywood panels and you realize that you must trace a straight line in order to make the cut. In the event that you do not have a straight edge near by You’ll probably be tempted to make use of one of the new boards. Since it’s straight from the factory, don’t you think?

But not so fast! Although some factory edges might be straight and exact but that’s not the norm. If you require a straight edge, you should use one you are sure is reliable. It could take longer than simply picking up an additional board however it could help you avoid a lot of hassle over the long haul.

Chalk Line Mastery

A single of the essential jobs site-specific skills to acquire is to outline tasks with chalk lines. This tool is utilized to do everything from determining the the plum to drawing flooring patterns for hardwood and tile this extremely useful tool is an absolute essential item for every DIY tool bag. Perhaps our most-loved hack for drawing chalk lines a quick technique for marking angle cuts on the wall. A small cut along the line that you want to cut require to tie or wrap the chalk line, making sure you have sufficient tension for marking the cut.

Labeling Cabinet Pull Locations

Don’t do the repetitive measuring and remeasuring process when installing pulls for cabinet drawers. The factory drawer faces must have square faces (but double-check as per the previous suggestion!) Therefore, you should draw a pair of lines that are from opposite corners. The lines will cross in the middle of the drawer’s face. With that easy trick and you’re all set to drill!

The right Scribe for the job

In theory, a lot of the work of woodworking and drywall is simple, just setting flat against the flat end. However, flat surfaces are not common and require an array of precise cuts, and occasionally a clever trick to get uneven surfaces to fit together in a smooth. A key part of this skill set is not just knowing how to scribe but also which tools to employ when the time comes to start. It could be as simple as using a tool that is specialized or a custom option (like clothingpin’s scribe that was mentioned earlier)

The marking of an arc or circle

If you’ve ever had difficulty to draw precise arcs and circles, this trick is for you! With a ruler, or a yardstick, be sure to mark a 1/8-inch hole around each inch. Set a pin or auger in that first opening (at one-inch marks) in the area you want the arc or circle to be centred. You can add 1″ to the diameter you’d like to draw, then put a pencil in that modified number. Make use of this pin to pivot, and turn the pencil around to mark the arc or complete circle. A huge thank you to our reader Edwin Constantino for this tip!

Advanced Arcs

This last suggestion was fantastic however, if you require an irregular or odd-sized curve, you’ll have to take your marking skills up to the next step. You can create arcs of much greater size using this trick: sketch out the plan of your arc, calculating the bottom corners and the peak and then putting nails or dowels on those corners as well as at least one of the corners at the top. Set two flat pieces of stock onto the plan. One bent from the bottom towards the peak, and the second from the peak towards the top corner opposite. Attach both pieces together together, then put a pencil into the junction. Place the stock pieces on the bottom and peak corner markers. Your pencil will draw an exact line.

Arcing with the help of a Speed Square

The majority of people have the Speed square in their toolkit However, few actually utilize them to their fullest potential in the area of marking cuts. A simple trick is to hook the notch at the top of the Speed square onto a nailand then make use of a pencil to draw small circles. To mark angles by tilting your square so that the angle of the blade of the square is the angle you’d like to.

Make sure you use the correct marker

We’ve been talking a lot about the tools that allow us to identify our marks however, it’s now time to look to the items that make our work. An easy way to help you make your life easier is to have a range of tools in your arsenal.

Pencils work well for a variety of reasons, but based upon the softness as well as the shade of lead used, it might appear too dim to be seen on certain types of materials. Sharpie markers are excellent and are simple to read however, while they might be appealing to use on surfaces like drywall, be aware that if you do plan to cover the marks with paint they’ll need to seal the area with a special primer, and perhaps paint several coats to cover those marks. Pens feature a beautiful slim line and don’t require to be sharpened. However, they aren’t able to withstand punishment the way that a pencil does take, and (like markers) they aren’t able to be erased. Also, if you’re using a gloss finish material like ceramic tile or PVC you should keep an oil-based pencil on hand so that your marks will be visible and easily removed.

Plumbs, Bobs and Levels

Learn to utilize plumbs, bobs, and levels to maximize the marking process. If you use these tools correctly will allow you to mark your work quickly and begin the actual task of assembly. Sometimes, a quick hack will make it even easier! A simple keychain laser can be transformed into a plumb-bob by using some string that is strong and, just like that you’re all set to make your mark!

Smarter Graph Paper

One of the most efficient method to make sure that you’ve got your idea clear and clear, particularly when you need to explain your ideas to others and draw the idea out. It can be difficult to transfer a 3D idea onto a 2-dimensional surface even using graph paper and drawing aids. Fortunately, this trick makes the planning process go easier! Isometric drawing pads complement standard graph paper grids using diagonal lines. This makes it easier to show the exact shape of your idea on paper. And you do not require an art degree for it.

This is particularly helpful in the planning phase of a big or complex project, such as an entire house renovation.

Kerf-Width Pencil Lead

One common error made by beginner DIYers is to not consider the blade’s width when calculating cuts. One way to get around this is to cut the pencil of your carpenter to fit the width of the saw blade. Mark your measurements on the cutoff end of your measurement so that you’ll know precisely how much material left, which is a major time-saver when you plan multiple cuts on the same panel or board.

Efficient Landscape Marking

When it’s time to tackle your landscaping, it may be tempting to use a hoe or shovel and start digging without properly taking measurements and tracing the plan. Instead, make sure to perform the equivalent of an “dry fit” like you would do when making furniture. Spray landscape paint the outline of your design on the grass. It’s not permanently fixed and will be wiped away by the next rain. You could scrub or cut it away.

In the event that your finances are limited, you can save a few dollars and make use of a length pipe to make an elongated boundary that is adjustable and modified as you the need. This type of marking allows you to move forward without fear and help you save time when working on your landscaping project. In actuality you’ll have plenty of time to spare that you’ll have the chance to take a look at these eleven more landscaping tricks that will save you time!

Marking Painting Boundaries

Many people are aware that you can use painter’s tape to create a clear lines when drawing. But what happens if you want to create a unique boundary layout, or perhaps one that has unruly edges? It turns out you can make it easier with this trick in the October Issue of Family Handyman. This trick involves make layers of tape that mark the boundaries, and then tear off edges to aid in feathering the layers.

DIY Marking Gauge

A part of the tool-modification group of techniques, this simple and simple trick will let you turn an ordinary combination square into an effective marking gauge.

Begin by drilling a 1/8-inch hole on the 1-inch line of the square combination. Make sure to center it precisely at the 1-inch mark ensure that you make your hole parallel to the square (use the drill press, if you have one). After that then you’re done with the most difficult part of the process! Set the combined square one inch over your desired measurement and then insert pencils in the 1/8-inch hole. Slide your square over the edge of the material. Your pencil will draw a sharp line in the exact distance you require.

DIY Board Center Finder

Finding the exact center of a board may be difficult however this trick can make it easy to locate an area that is dead centre and draw a line around it. With a piece of 3/4-inch wood and dowels that measure 1/2-inch to create an U shape with a pencil hole at the center. As long as the wood you’re marking is able to fit inside the dowels, find the middle, then use your instrument (and your pencil) through all the way.

A Faster Crown Molding Installation using an Angling Gauge

This marking technique comes as part of the 3 piece crown molding installation, which simplifies the entire process. When you install the central part of the crown with two pieces of pre-cut straight trim you’ll get more flexibility in dealing with irregular corners and walls. To get there using the marking gauge. Take a measurement of the drop and run of your crown after which you can join the two block to create an L-shape that is reversed. Then, place it against the trim to align the crown’s center.