10 Secret Power Tool Hacks for DIYers

Are you aware of all the secrets of making use of your drill or driver? Discover the full possibilities of the power tool using these innovative hacks for your tools.

Simple Eye Hook Removal

Ye hooks are terrific little fasteners that can be used for a variety of uses. However, taking them off can be quite an inconvenience particularly when you attempt to remove them manually.

In lieu of having to put your fingers into a plethora of pain Try this easy trick to get rid of eye hooks The trick is to insert your allen wrench’s long side in the drilling chuck, and then utilize the hook’s side to turn the hook away. It’s that simple!

Eliminate Drywall that is caked on Drywall

In the ideal scenario, drywall knifes are cleaned almost in the same day all the mucking work is finished. The mud that is used to finish the walls is (obviously) easier to wash up after it hardens and dries. However, don’t fret in the event that you have knives that have been smothered in mud caked on that they’ve lost their use.

Instead, get out your preferred Random Orbit Sander and begin working. Select a grit that is approximately 120 and then rub off the dried-on mud the same way as you’d sand remove mud from the wall. Make sure that you’re not too rough and don’t end with harming the blade.

The Best Way to Wrap Tie-Down Straps Up

The most effective way to stop the tie-down straps from turning into a huge messy mess is to fold them up after you’ve finished using them. Here’s an easy method to do that.

Create an “specialty tool” which is actually an 1/4-in. dowel, with a notch on the top. Create the notch length of the length of your strap. Put your dowel into a drill with the notched portion sticking out.

All you have to do is slip the strap’s end into the notch of the dowel, and then turn the dowel at a slow speed. Dowel spins the strap into an elongated circle before wrapping around it to form a tidy, circular roll.

Make Your Eyes Do You a favor and save a shoebox

Inhaling dust can be dangerous and generally not a lot of enjoyable. When you’re drilling into the ceiling, often the most effective eye protection doesn’t seem to be able all the tiny particles which flutter from above determined to find and settling in the pupils of your eyes.

There’s a simple solution. If you’re ever forced to drill several holes into the ceiling, get an empty shoebox from the back and stick your drill through it until the opening of the box is facing in the same direction as the drill bit. Attach your drill to the drill and start working. It will absorb the large portion of dust that gets deposited in the hole you have created, saving both your eyes and the time spent cleaning up.

Are you looking for a hole in the hard soil? Make use of a drill.

Did you wait for too long to put up your reflective driveway markers only to found that your driveway was covered in snow? Have you tried installing an outdoor yard sale sign in dry soil that’s as tough as concrete?

So, why not treat it like it were concrete and then drill holes in it using a masonry drill? This 3/8-in. 12-in. Bit is available online.

Lift Stuff that is Heavy with the help of a flat Pry Bar

If you’ve needed to take a door that is solid core and hinges, you’re aware of how heavy they are. The process of lifting them to replace the hinge pins is a hassle especially if you’re working on your own however using a simple pry bar (aka “flat bar”) can provide you with the strength you require.

If the flat bar can’t raise the door sufficiently you can place a small piece of wood on the fulcrum of your pry bar in order to increase the distance of lifting. Secure the block with a screws and washer. Make sure the screw does not go through the. Should it do, you can grind off the ends so it doesn’t cause damage to the flooring. The same technique can be used to lift the drywall’s bottom off of the floor to secure them.

The Best Method of Cutting Through Foam

If you make a mistake the process of cutting foam could be quite messy. The serrated teeth on a saw blade can break and tear foam, sending tiny foamy bits of it floating through the air. Then, those tiny bits stick to anything and are difficult to get rid of.

It’s not difficult to find a method of creating an instrument that can cut through foam without cutting it in pieces. Before you attempt to cut the foam, you should use a well-used cutting jigsaw blade, and then, securing it using a pair locking pliers, cut off the teeth to create an edge that is smooth. Your Jigsaw will provide you with an attractive, smooth cut through foam each time.

Long-Reach Screwdriver

If you want to extend the range of your electric screwdriver simply pull the shaft out of the four-way screwdriver. Then fix it into the chuck.

A Simpler Depth Stop

You’ve probably seen the method using applying the electrical tape to mark the drill bit to stop the hole at a particular depth. This is a fantastic idea but when you drill multiple holes, that tape may become quickly ripped when it happens. Once that happens it’s not an accurate depth stopper.

Instead, opt for an permanent marker to show the depth you want to target and you’ll see more usage of it, before it gets damaged. After you’ve completed your work, just wipe the drill bit clean with removal of paint and Goo Gone and the marker’s ink will be able to come off.

To make this method more efficient, you’ll need to pick a marker colour that is distinct from your drill bits. Ideally you’ll have a couple of markers in your toolbag depending on the kind of twist drill you’re using.

Blade Reciprocating Backward Blade

Recrocating saw blades do not have to be inserted with the teeth facing downwards. The blade can be reversed to cut flush, as you would after wall framing when you take sill plates off of doors.